lock nut

lock nut

美 　英

• un.〔机〕放松螺母；对开螺母；锁紧螺母；锁紧螺帽
• 网络防松螺帽；防松螺母；锁定螺母

英汉解释

un.	1. 〔机〕放松螺母;对开螺母 2. 锁紧螺母 3. 锁紧螺帽 4. 锁锭螺母 5. 防构螺帽 6. 保险螺母 7. 防松螺母

例句

Disassemble the door-frame, loosen the lock nut, and hammer it out.

分解门锁，松开锁住部分，然后将折断部分敲出。

Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle .

孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。

Can counterclockwise unscrewing the grip the lock nut and adjust control again, until the nut spin twist clearance fit.

可以逆时针拧松握把根部的锁紧螺母，再左右旋拧调整螺母，直到间隙合适为止。

The problems in lock nut of roll axis and sleeve of precision rolling mill are analyzed, some measures proposed, good result got.

针对高速线材生产中，精轧机辊轴及隔套锁紧螺母存在的问题进行分析，提出了改进措施，取得了较好效果。

Disc is fastened securely to disc hanger with a lock nut and cotter pin .

通过一个锁紧螺母和开口销将阀瓣安全紧固在阀瓣支架上。

After completing adjustments, tighten the lock nut and replace the fast fill lever cap.

在调节完成后，紧固锁紧螺母，重新安装快速进水手柄帽。

The two-piece Hard Lock Nut is easy to install, requiring only the use of a wrench.

双件套强力锁紧螺母安装简便，只需要一个扳手就行。

lock nut holds the setting at the precise measurement.

防松螺母使设置保持精密的测量。

I know what I'm doing. I don't need any lock nut.

我知道我在做什么我不需要什么螺母

V. Notes 1. Replacement blades to compress the lock nut, otherwise, saw people flying out of injury accidents caused by equipment;

五、注意事项1.更换锯片必须锁压紧螺母，否则，锯片飞出造成设备人伤事故；

LOCATING CONE LOCATION KEY LOCATION PIN LOCK BEAD LOCK NUT CHAIN STEEL LOCKER LOWER MCS(MASTER MAGNET CONTRL SURFACE)

装料（装载）重量支撑、限止器定位锥定位键定位销拉延槛锁紧螺母链条下刀块

The strap tension force is adjusted ex works with the aid of hex cap lock nut

扎带的张力是通过六角头锁紧螺母来实现的

Measuring the lock nut tightening angle

测量锁定螺母的拧紧角

Loose optical wedge lock nut (No. 7 in Fig. 1) at both sides of sighting telescope center by special wrench;

用专用扳子将瞄准镜中部左右两个光楔锁紧螺母（图1序号7）松开；

Clamping sleeve with lock nut

带锁母的夹紧套

Difference in shaft lock nut

轴差内锁紧螺母

Motor half coupling lock nut

电动机半联轴器的锁紧螺母

check (or jam, or lock) nut

锁[紧螺]帽，并紧螺帽